details.

Als die Hersteller der weltbesten Lüfter, hatten wir eine Pflicht zu erfüllen....das leiseste Netzteil der Welt! Unsere Netzteile laufen leise und stabil dank einer innovativen Technologie die nur SilenX verwendet.

Die iXtrema Pro ATX Netzteile sind hoch effizient und eine der wenigen PSUs auf dem Markt die mit Copper Heatsinks ausgestattet sind. Die iXtrema Pro Lüfter werden für den Betrieb mit niedrigem Geräuschpegel verwendet und das patentierte SilenX PowerpipeTM Baukasten System der zweiten Generation für die schnelle und einfache Installation der Kabel. Das modulares Kabelmanagement erlaubt dem Anwender, das Netzteil entsprechend des Umfangs des eigenen Systems individuell zu konfigurieren. Es werden lediglich die Stromkabelstränge angeschlossen, die tatsächlich benötigt werden. Im Sinne einer optischen Aufwertung und einer aufgeräumteren Alternative zur herkömmlichen Verkabelung werden die Kabelstränge als Airflowkabel geliefert.

the silenx advantage.

Ein nach vorne gerichtetes Schaufeldesign erhöht den statischen Druck und sorgt damit für besseren Luftdurchsatz im Gegensatz zu anderen leisen Lüftern verschiedener Hersteller. Zusätzlich erreicht SilenX mit dieser Technik auch eine verbesserte Durchlüftung schwieriger Stellen.
Die verringerte Motorengröße und eine konische Form der Motorengehäuseabdeckung erlauben eine größere Oberfläche der Schaufelräder und verbessern damit die Aerodynamic bei gleichzeitiger Verringerung des sogenannten "Hot-Spots".
Das modulares Kabelmanagement erlaubt dem Anwender, das Netzteil entsprechend des Umfangs des eigenen Systems individuell zu konfigurieren. Es werden lediglich die Stromkabelstränge angeschlossen, die tatsächlich benötigt werden. Im Sinne einer optischen Aufwertung und einer aufgeräumteren Alternative zur herkömmlichen Verkabelung werden die Kabelstränge als Airflowkabel geliefert.

choosing the right power supply.

Use the following guide to choose the power supply that is right for you:

First and foremost, check which form factor your system uses. ATX is the standard PSU form factor for an overwhelming majority of the systems out there, and measures 140x150x86mm, which is approximately 5.5x5.9x3.4in. SFX power supplies are used on smaller and slimmer cases, such as those on HTPC systems and measure 120x125x63.5mm, or approximately 4.7x4.9x.2.5in.

Once you've determined the form factor, determine the wattage for your system requirements. Generally the higher the performance of your system, the more power you need. Figure around 250 watts for the highest end processors and motherboards as your base figure and about 100 watts for lower end systems.

For high end graphics cards, add about 80 watts, and about 40 watts for lower end models. Keep in mind if you're using SLi or CrossFire, double that figure!

Depending on the performance of your hard drives, add about 15 to 30 watts each. Higher RPM doesn't necessarily mean more power consumption, rather, it's the total inertial mass of the spindles, so if your hard drive has more spindles, those will naturally consume more power. 15K drives have smaller spindles than 7.2K drives and sometimes consume less power despite their incredibly high RPMs.

Optical drives can consume quite a bit of power when you're burning CDs or DVDs. Figure a good 30 watts per drive to give enough leeway.

Factor in another 30-50 watts for other peripheral devices, such as sound cards, TV tuners, USB devices and so forth.

As always, add a few more watts to take into account any future upgrades you might consider down the line, and make sure you have adequate ventilation in your system. Power supply fans are never designed to vent both the system and the power supply itself!